The service life of ceramic mosaic tiles
Wear mechanism of wear-resistant alumina lining: According to different working conditions and stress conditions, the wear of wear-resistant ceramic linings can be roughly divided into cutting wear, fatigue wear, abrasive wear, impact wear and other categories. The working principles of wear are not the same, so the wear mechanisms of ceramic sheets are also quite different, and in practical applications or tests, they often do not act in isolation, but are interconnected and affect each other, and sometimes a mechanism is obvious. Sometimes it is a combination of two or more mechanisms.
Service life of wear-resistant mosaic linings: In addition to its own quality, the service life of wear-resistant ceramic linings is an important factor that is external factors, which mainly include medium particle size, hardness, friction mode, environment, load, and scouring speed. , temperature and time, etc. Generally speaking, the smaller the particles, the lower the concentration, the lower the scouring speed, the smaller the scouring angle, and the longer the service life of the wear-resistant ceramic sheet. Usually in the network pipe of the slag micropowder production line, the specific surface area of the micropowder is 420-450m2/kg, the concentration is 350g/Nm3, the speed is 28-30m/s, and the scouring angle is 30°C, 20mm wear-resistant ceramic sheet can be used 8 to 10 years. Raw and clinker mills are easier to grind than slag, and wear-resistant ceramic sheets of the same thickness have a service life of more than 10 years.
Performance characteristics of microcrystalline wear-resistant alumina lining:
High hardness, wear resistance and erosion resistance: 92 porcelain, 95 porcelain alumina wear-resistant ceramic plate, Rockwell hardness is HRA85-95, comparable to diamond, resistant to The grinding performance is much higher than that of manganese steel and high-friction cast iron, which can prolong the service life of the equipment by more than 10 times under the same working conditions;
2. Excellent high temperature and heat resistance: it can run for a long time at 750 ℃;
3. Acid and alkali resistance Corrosion: Alumina wear-resistant ceramic sheet has stable chemical properties, acid and alkali corrosion resistance, anti-oxidation, and is suitable for various harsh working conditions;
4. Light weight: The density of the wear-resistant ceramic sheet is 3.5-3.8g/cm3, only steel
5. Firm bonding and not easy to fall off: the wear-resistant ceramic sheet can be fixed by high temperature inorganic adhesive, arch joint and stud welding, etc., which can ensure that the ceramic sheet can withstand high temperature and high impact Long-term operation under conditions does not fall off.
The process of repairing the pipeline with wear-resistant alumina lining: cleaning the surface of the pipeline → repairing the body → grinding and smoothing → pasting this article → welding → testing the thickness → self-inspection.
Preparations: material procurement, commissioning equipment, construction personnel arrangements, power connection, gas source and other preparations.
Clean the surface of the pipe: effectively remove dirt, rust and other debris.
2. Grinding: Use an angle grinder to treat the pipe wall, requiring no rust and looseness on the pipe wall. Construction in an environment with a humidity greater than 85% is strictly prohibited to ensure that the quality of the project reaches excellent standards.
3. Isolation measures: After removing sundries, it should be kept in an electrostatic dry environment to prevent dust pollution.
4. Paste the microcrystalline wear-resistant alumina lining: mix parts A and B according to the proportion, paste the ceramics after evenly mixing, and grind the ceramic parts evenly, without virtual adhesion and protruding phenomenon, the wear-resistant ceramic layer is smooth, and the plate and the plate are smooth. The gap is less than 0.4 mm. The seams of the ceramic plates are smooth.
5. Welding: Place the hardware glue in the hole of the ceramic liner, weld the full-length welder, and stick it on the hardware surface with a ceramic cap.
6. Self-inspection: After the ceramic parts are pasted, carry out self-inspection, reprocess the unqualified parts, and then carry out self-inspection.
Wear-resistant technical advantages of wear-resistant mosaic linings:
1. The hardness is higher than HRA 86, and the hardness is second only to diamond, far exceeding the wear resistance of wear-resistant steel and bimetallic composite plates. The wear-resistant ceramic sheet is made of 95% Al203 with a variety of unique wear-resistant material formulas, which have the characteristics of high density, high toughness and wear resistance.
2. Excellent wear resistance, the wear resistance is 266 times that of manganese steel and 171.5 times that of high-chromium cast iron. Under the same working conditions, the service life of the equipment can be extended at least ten times.
Fourth, Cr203 and TiO2, which are very similar to A1203 lattice, are introduced into the formula of impact-resistant and wear-resistant ceramics. At the same time, zinc oxide whiskers are added in the sintering process to form solid grains with A1203, refine the grain size, promote sintering, and improve fracture toughness.
4.The fracture toughness of fine wear-resistant ceramic products is kic (>4.8Mpa/m).
5. The adhesive has strong strength and good heat resistance. Ensure that the wear-resistant ceramic sheet does not fall off for a long time at high temperature.







