1. The way to reduce the "breakage rate" of ceramic ball according to the experience of the research and development of ceramic ball application technology in the past year, the following is briefly introduced
(1) adding "toughening" elements in the batching scheme: ceramic ball is an inorganic non-metallic material. When its hardness and wear resistance reach a certain degree, the weakness of insufficient toughness is obvious.At present, the lining board and components inside the ball mill are made of cast steel, and the movement state of its grinding and grinding materials is also carried out in the complex and alternating environment of rolling, sliding, impact and collision.Therefore, while grinding the material, the ceramic ball itself is also subjected to different forms, different directions, different sizes of the reaction force.At this point, in addition to wear resistance, corrosion resistance, impact toughness, it is very important.And specially for dry cement grinding and the development of ceramic ball products, must add trace elements (such as zirconia, etc.) modified toughening, in order to ensure that it is not only high strength, but also has good toughness

(2) preferred forming method: there are two kinds of common ceramic ball forming methods: pressing ball and rolling ball.Due to the difference of technological process, the internal crystal structure of the spherical stone after molding and roasting is different, and the degree of compactness and impact resistance are also different.Through many and repeated destructive tests, we found that: in the process of grinding cement material, the damage rate of pressing ball with the same material and the same specification is lower than that of rolling ball.
(3) ceramic ball is not suitable for impact crushing of ball mill: in the process of cement grinding, when the abrasive particle size is more than 5mm, the abrasive body in the first bin of the ball mill needs to be in the throwing state. The impact crushing effect is mainly used to crush large materials into fine particles.At this point, the abrasive body is not only subjected to a strong reaction force, but also inevitably collide with the dense cast steel lining board, compartment board and other components;Therefore, such a working condition is not suitable for the work of ceramic balls with limited toughness, or a high breakage rate will occur.
(4) short positions when grinding, first add ball: after charging, the cement industry in China has been forced to eliminate 3 meters of ball mill, each enterprise in the grinding mill when loading, use electric hoist crane handling the ball, drop in at this time more than 3 meters, ceramic ball discharge land on cast steel plate, sphere internal causes varying degrees of micro cracks, affect the service life of ceramic balls.Therefore, when loading the mill in the empty warehouse, 2-3 tons of materials (or bulk cement) should be added first to ease the impact and protect the ceramic ball.
2, the solution to reduce the output of the grinding system in the cement industry, many people mistakenly think: "there is no technology in the application of the ceramic ball, is not the ball mill end of the steel out of the tank to replace the ceramic ball?In fact, the result of doing so is that the output of the grinding system can only be reduced again and again, the reason is very simple, do not reduce the output, the content of qualified cement products in the grinding logistics is too little, to ensure that the quality of cement products (fineness, specific surface area) to achieve the internal control index, it is necessary to reduce the output.Many in the cement mill workshop work for more than ten years or decades of staff, do not believe this reality at the beginning, according to the use of steel ball, steel forging experience of the application of ceramic ball, ball mill table when the output of a sudden fell by 20%-30%, and then add more ceramic ball, the problem can not be solved.Only at this point, you have to admit: the application of ceramics, both to the grinding system to save electricity, and can not reduce the production of cement, quality.And this is the ceramic ball application technology technology content.The hardness and wear resistance of ceramic ball are no less than that of steel ball.We through a number of small grinding tests, have confirmed this: in the same specification, the same load, the same grinding time, ceramic ball and steel ball grinding cement production, quality, basically the same.Why does the difference show up in the big mill?The reasons are as follows:


(1) the bulk density of the ceramic ball is 2.2t/m3, while the bulk density of the steel ball is 4.5t/m3. In the same cabin of the ball mill, the ceramic ball generally cannot have the same loading quantity as the steel ball or steel forging. If the loading quantity is the same, the volume (or filling rate) of the ceramic ball must be twice as much as the steel ball or steel forging.However, the limit value of ball mill filling rate is, must be less than 50%, so, the capacity is light, is the ceramic ball to save the cost of electricity, at the same time is "can not exceed the limit" drawback.
Dry grinding cement ball mill is a continuous working equipment for grinding head feeding and grinding tail discharging.Generally, the material stays in the mill for only 18-20 minutes from the import to the export. The length of the tail bin of the large ball mill is 8-9 meters, and the material stays for the longest time is within 10-15 minutes.The ceramic ball is limited by the filling rate, the loading amount cannot be increased, and the grinding time cannot be prolonged. To fine the material and meet the requirements of the enterprise's internal control index, this is the problem: the grinding capacity of the ceramic ball is not on the same order of magnitude as the steel ball and steel forging;In other words, the ceramic ball cannot compete with the steel ball and steel forging on the "same starting line". The steel ball in the forward bin, and even the pre-crushing (roller press) system extending to the front of the mill must "leverage" to make the materials entering the final bin finer than the steel ball and steel forging.Without the previous help, it must "lose the chain" in the tail bin.Before the application of ceramic ball, if these two points did not see, do not understand, the ball mill "output", that is to be expected.
Before the ceramic ball application, we must open the grinding door, into the ball mill, measuring the actual filling rate of each bin grinding body (calculate the actual load), do know;After several large grinding tests, we explored a set of simple solutions in the cement grinding system with grinding size ≤5mm: "air height operation";I.e., before the use of ceramic ball inside a warehouse (ball), according to the basic principle of constant average ball diameter ball, until the warehouse in the high ratio of H/Di (on the surface of the grinding surface space height H and the ratio of the effective diameter Di) to achieve a suitable range: 0.55 (cap) to 0.60 (lower limit), it corresponds to the maximum filling rate is about 43%, lower at about 37%;Too low, too high is no good.After that, as long as the loading quantity of ceramic ball in the tailstock reaches 60% ~ 70% of the original loading quantity of steel forging (or small steel ball) in the tailstock, the expected target will be achieved, and the output of the cement grinding system will not be reduced or only slightly (≤5% of the original output).
Some cement companies reported that their ball mill ball filling rate more than 30%, the ball is not added.So what do we do?The reason is that in the design parameters of some home-made ball mills and large sliding shoes mills, the metal abrasive body (steel ball, steel forging) is the reference object. The loading amount of a warehouse should comply with the needs of impact crushing, and the filling rate is generally not more than 30%.Therefore, the design size of feed inlet of grinding head is too large without considering the need of increasing filling rate in the future.If it is such a mill, then before the use of ceramic ball, the inlet should be properly modified, add a feeding screw, reduce the size of the inlet, can be added to the steel ball.
For cement enterprises, the application of ceramic ball technology has developed a new way of energy saving of cement grinding.In the new innovation-driven environment, it is inevitable that we will encounter some twists and turns.As long as we carefully operate, seriously summarize, we will be able to learn, understand, master the technology in the shortest time, the economic benefits of the enterprise to reduce costs, add luster





